|
|
   
Hipot / Dielectric Strength Testers
 A DIELECTRIC STRENGTH TESTER PROVIDES A HIGH VOLTAGE TEST IN ORDER TO CHECK THE QUALITY OR SOME CURRENT LIMITS DEFINED IN THE INTERNATIONAL STANDARDS
This high voltage test (also called dielectric strength test, hipot test, hi-pot test, breakdown test or flash test) is made to stress the device under test to an AC or DC high voltage and check that there is no breakdown nor perforation happening. It also checks that insulation distances and distances in the air are respected.
Dielectric Strength Tester RXS50
Reference: RXS50
Product description: Designed as well for laboratories as for production lines, the XS Series is our new Electrical Safety Tester generation.
Cheaper, faster, better, based on new technologies, the XS Series can offer advanced features such as optimized accessory management, Ethernet interface, faster test times, and industrial interfaces.
Product details:
• Hipot up to 5 kV AC 10 mA nominal current / 13 mA short circuit current
• fully automatic testing
• standard RS232, optional IEEE488-2, Ethernet, or PLC
• SXSPRO multi-lingual software
• easy to use and user friendly interface |
back to top | Email Electri-Temp. Corporation
Dielectric Strength Tester RXS500
Reference: RXS500
Product description: Designed as well for laboratories as for production lines, the XS Series is our new Electrical Safety Tester generation.
Cheaper, faster, better, based on new technologies, the XS Series can offer advanced features such as optimized accessory management, Ethernet interface, faster test times, and industrial interfaces.
Product details:
• Hipot up to 5 kV AC 110 mA nominal current / 200 mA short circuit current
• fully automatic testing
• standard RS232, optional IEEE488-2, Ethernet, or PLC
• SXSPRO multi-lingual software
• easy to use and user friendly interface |
back to top | Email Electri-Temp. Corporation
Dielectric Strength Tester DT-all-in-one
Reference: DT-all-in-one
Product description: Each model is built according to voltage and current customer requirement for hi-pot testing, in order to keep our low cost policy.
Product details:
Hipot tester with cage:(C)ompact presentation
• AC/DC dielectric strength test
• PLC control, RS232 interface, 0-10 volts control
• manual, automatic or programmable command
• complies with the following safety testing standards: EN61010-1, EN60065, EN60335-1, EN60598-1, EN60601-1, EN60950, CEI990, and many others
Transportable tester, only some small power transformers can be integrated in such a rack. It also has the panel control you choose, either manual (M), automatic (A) or programmable (P).
This system must be associated to safety cage with safety loop, to detect the opening of the cage.
One / several 5 meter of shielded HV cable is / are provided to connect the control panel to the transformer. specific grounding is made for DC generators.
Security:
Safety loop on the back of the command unit.
Grounding relay on DC generators.
Thermal security for protecting the command unit and generator.
Possibility of contact outputs or 24V for supplying external safety devices. The operator must insure the protection of people against contact with high voltage (safety cage, etc.). |
back to top | Email Electri-Temp. Corporation
Dielectric Strength Tester DT-with-cage
Reference: DT-with-cage
Product description: Each model is built according to voltage and current customer requirement for hi-pot testing, in order to keep our low cost policy.
Product details:
Hipot tester with cage:(C)ompact presentation
• AC/DC dielectric strength test (also called flash test, hi-pot test or high voltage test)
• PLC control, RS232 interface, 0-10 volts control
• manual, automatic or programmable command
• complies with the following safety testing standards : EN61010-1, EN60065, EN60335-1, EN60598-1, EN60601-1, EN60950, CEI990, and many others
Developed for testing samples of small or medium volume, only some small power transformers can be integrated in such a rack. It also has the panel control you choose, either manual (M), automatic (A) or programmable (P).
This system includes:
• safety loop including a switch cutting of the high voltage when the door is open
• specific grounding for DC generators
Security:
Safety loop on the back of the command unit.
Grounding relay on DC generators.
Thermal security for protecting the command unit and generator.
Possibility of contact outputs or 24V for supplying external safety devices. The operator must insure the protection of people against contact with high voltage (safety cage, etc.). |
back to top | Email Electri-Temp. Corporation
Dielectric Strength Tester DT-separated-units
Reference: DT-separated-units
Product description: Each model is built according to voltage and current customer requirement for hi-pot testing, in order to keep our low cost policy.
Product details:
Hipot tester with transformer and control unit in 2 different modules: (S)eparated (U)nits presentation
• AC/DC dielectric strength test
• PLC control, RS232 interface, 0-10 volts control
• manual, automatic or programmable command
• complies with the following safety testing standards : EN61010-1, EN60065, EN60335-1, EN60598-1, EN60601-1, EN60950, CEI990, and many others
This type of configuration can be chosen with any transformer.
It also has the panel control you choose, either manual (M), automatic (A) or programmable (P).
This system must be associated to a safety cage with a safety loop, to detect the opening of the cage.
When you choose separated units, that means you will get the control panel integrated in a housing on the one hand, connected through a cable to the transformer unit (such as model DT1, DT2 or DT3) on the other hand.
One / several 5 meter of shielded HV cable is / are provided to connect the control panel to the transformer. specific grounding is made for DC generators.
Security:
Safety loop on the back of the command unit.
Grounding relay on DC generators.
Thermal security for protecting the command unit and generator.
Possibility of contact outputs or 24V for supplying external safety devices. The operator must insure the protection of people against contact with high voltage (safety cage, etc.). |
back to top | Email Electri-Temp. Corporation
Supernova Plus Portable Hipot Tester
The world's most comprehensive Portable Tester
The Supernova Plus unit is a dual voltage tester. Radical new features ensure that the Supernova Plus unit allows you to test virtually any electrical device, using any supply, giving you absolute flexibility in your testing procedure.
To enable test operators to determine progressive deterioration or potential faults in the equipment under test, the Supernova Plus incorporates specially developed software that compares successive test results taken on the same item of electrical equipment.
The Supernova Plus incorporates a number of new innovative features to make electrical safety testing faster more convenient for the operator. These include:
The unit has increased data storage capacity to enable up to 6000 memory locations. Ability to perform in-line testing for ground bond and touch leakage while the equipment remains powered up — greatly reducing test times.
Inclusion of two serial ports for the concurrent use of a bar code scanner and a printer. This enables the user to print results immediately after a test has been completed.
Ground cable length calculator to set ground bond limits, and the automatic increment of device IDs, to further speed up the test process.
Compatible with our powerful management software, PATGuard, The Supernova Plus provides a complete electrical safety testing solution. The new Supernova Plus test unit comes with FREE downloadable software in order to ensure the testing and information gathering process is as convenient as possible (PATSLite).
Key Features
Standard Features
• Accurate Ground Bond and Leakage Measurements even when multiple Ground Paths exist
• Multi Voltage In/ Multi Voltage Out
• Has up to 6000 Memory Locations
• Dual Voltage test capability
• Modem Capability
• Summary Format
• Polarity Lead Test capability
• Tests IT equipment
• Real time clock and non-volatile memory
• Capable of printing barcode labels in conjunction with thermal printer
• Connects to PC, barcode reader, Brain Cell RFID Scanner and printer
• Compatible with our PATGuard management software.
• Parallel printer port.
• Auto test code generation.
• User defined HELP Screens.
• Superfast download up to 10 times quicker than existing testers.
New PLUS Features
• Performs in-line Ground Bond and Touch Leakage tests while the equipment under test remains powered up — greatly reducing test times.
• Unit incorporates Results Comparison Software.
• 2 Serial Ports — use a bar-code scanner and printer together.
• Ground Cable Length Calculator.
• Automatic Generation of Device ID's.
• Single Screen Visual Test.
• Includes FREE Downloadable Software - PATSLite |
back to top | Email Electri-Temp. Corporation
SafeCheck Manufacturing Hipot Tester
Ideal for improving productivity and efficiency in low to medium volume testing
Developed specifically to offer some of the productivity and efficiency benefits associated with sophisticated high-end equipment.
Unlike typical in-service PAT testers, this Hipot tester offers the correct flash/hipot test to meet the CE and international requirments for routine product testing during manufacturing. In-service PAT testers have the test output limited making them unable to meet this legislatory requirement for use in routine production line testing. If you require further clarification on this point, why not call Seaward Group USA and we will be happy to give clear and concise examples taken from over 50 years of dedicated service to the manufacturing industry.
SafeTest Manufacturing can be used as a simple manual tester or with varying degrees of automatic test sequencing and performs earth bond, insulation resistance, flash/hipot, leakage, short-to-line and run/load tests.
Easy to operate with via full QWERTY keypad and or barcode scanner, and includes full on screen user instructions. The new SafeTest hipot tester has been designed to meet the needs of manufacturers that require a range of fundamental safety tests to be carried out on a variety of electrical and electronic products.
All tests are individually user selectable and an internal memory has the capacity to store the results of 6,000 tests. The new tester also comes with an optional safety label printer that enables the automatic production of test tags, labels and test reports. Clever use of the optional barcode scanner for product identification and tester configuration, enables this product to be integrated easily into a typcial ISO quality control system.
Special safety interlocks and protection routines provide enhanced operator safety and a full range of test station accessories can also be supplied, including warning beacons. The design of the test environment is an area that Clare is considered to be an expert. We can offer best practive examples from our diverse knowledge of test applications, so if in doubt why not give us a call.
Some Common Standards that SafeTest Manufacturing will test to:
IEC/EN/UL/CSA 60335 — Household and similar electrical appliances
IEC/EN/UL/CSA 60065 — Audio visual and similar electronic equipment
IEC/EN/UL/CSA 60950 — Information technology equipment
BS EN/SS EN 50116 - Information technology equipment, routine testing
IEC/EN/UL/CSA 61010 — Electrical equipment for measurement, control, and lab use
Key Features
• Optimised user interface to simplify setup towards the Manufacturing environment
• Provides correct flash/hipot test for CE and international product test compliance
• Flash/hipot test delivers up to 10mA of leakage unlike typical in-service PAT testers
• Full traceable test results, logged with real-time data and user
• Semi-automatic test sequences can be created to speed up test process
• Rugged ergonomic case
• Large high contrast graphic display
• Compatible with PATGuard software
• Barcode scanner or QWERTY keyboard can be used for entry of product serial number, test codes, and user details
• Barcode scanner can be used to automate test process
• Manual test mode facility for diagnostic testing
• Complies with EN 50191, has beacon and safety guard circuit
• Can be used with a generic printer, or Desk TnT label printer
• Dual function test output of 230 and 120 Volts, allows products to be tested for different geographic regions
• Flexible password protection incorporated within system configuration |
back to top | Email Electri-Temp. Corporation |
|
Data Acquistion | Decade Boxes | Digital Thermometers | Dry Blocks / Furnaces | Electrical Safety - Alphatek | Electrical Safety - Clare | Electrical Safety - Sefelec
Hipot / Dielectric Strength | Insulation Testers | Liquid Baths | Megohmmeters | Microhmmeters | Milliohmmeters | Power Quality | Resistance Standards
T/C Calibrators / Simulators | Temperature Standards | Weights and Balances | Test and Measurement Equipment Site Map
© 2008, Electri-Temp. Corporation, All Rights Reserved
New Hampshire (NH) Website Design Development
Alphatek, ASL, Calibration, Clare, Cropico, Data Acquistion, Decade Boxes, Digital Thermometers, Dry Blocks / Furnaces, Electrical Safety Tester, GMC,
Hipot / Dielectric Strength Testers, Insco, Insulation Testers, Isotech, Liquid Baths, Measurement, Megohmmeters, Microhmmeters, Micro Movements,
Milliohmmeters, Power Quality, Resistance Standards, Seaward, Sefelec, T/C Calibrators / Simulators, Techne, Temperature Standards, Weights and Balances,
Connecticut, Maine, ME, Massachusetts, MA, New England, New Hampshire, NH, Rhode Island, RI, Vermont, VT, United States, U.S., USA |
